Modifying the Mechanical Property of PLA-Carbon Fiber Composite Fabricated by FDM Via Adjusting Process Parameters and Heat Treatment
DOI:
https://doi.org/10.12974/2311-8717.2026.14.13Keywords:
Fused deposition modeling, PLA-carbon fiber, Mechanical property, Process parameters, Heat treatmentAbstract
Fused deposition modeling (FDM) has become one of the most widely used additive manufacturing technologies, while polylactic acid reinforced by short carbon fibers (PLA-CF) is increasingly applied in structural components. However, the mechanical properties of FDM-printed parts are strongly affected by printing parameters and show obvious anisotropy owing to weak interlayer bonding. In this work, PLA-CF composites with fiber mass fractions of 4 wt.%, 7 wt.%, and 15 wt.% were prepared by FDM. The effects of filling angle (0°, 45°, 90°), printing hatch (0.35 mm, 0.45 mm), and annealing treatment on tensile properties and mechanical anisotropy were systematically studied. The results show that filling angle dominates the tensile strength, which reaches the maximum at 0° filling angle due to favorable fiber alignment and load transfer. Reducing printing hatch can improve interlayer bonding and significantly enhance the strength of 45° and 90° specimens. The fiber mass fraction presents an angle-dependent influence on tensile performance. Moreover, heat treatment effectively reduces anisotropy. Vacuum annealing at 180°C for 3 h increases the tensile strength of 90° specimens by 105.6% and minimizes the strength gap between 0° and 90° specimens to only 2.5 MPa. This work provides a feasible strategy for preparing high-performance, low-anisotropy PLA-CF components.
References
Yuan S, Li S, Zhu J, et al. Additive manufacturing of polymeric composites from material processing to structural design. Composites Part B: Engineering 2021; 219. https://doi.org/10.1016/j.compositesb.2021.108903
Goh GD, Wong KK, Tan N, et al. Large-format additive manufacturing of polymers: a review of fabrication processes, materials, and design. Virtual and Physical Prototyping 2024; 19(1). https://doi.org/10.1080/17452759.2024.2336160
Zhang T, Lin X, Qin Y, et al. Multiphysics Modeling of Heat Transfer and Melt Pool Thermo-Fluid Dynamics in Laser-Based Powder Bed Fusion of Metals. Materials (Basel) 2025; 18(13). https://doi.org/10.3390/ma18133183
Bourell DL. Perspectives on Additive Manufacturing. Annual Review of Materials Research 2016; 46(1): 1-18. https://doi.org/10.1146/annurev-matsci-070115-031606
Abderrafai Y, Diouf-Lewis A, Sosa-Rey F, et al. Additive manufacturing and characterization of high temperature thermoplastic blends for potential aerospace applications. Composites Science and Technology 2023; 231.https://doi.org/10.1016/j.compscitech.2022.109839
Chrz K, Bruthans J, Ptacnik J. Clinical Application of FDM 3D Printing in Surgery and Traumatology: A Systematic Review. Ann Biomed Eng 2026. https://doi.org/10.1007/s10439-026-04021-z
Bere P, Neamtu C, Udroiu R. Novel Method for the Manufacture of Complex CFRP Parts Using FDM-based Molds. Polymers (Basel) 2020; 12(10). https://doi.org/10.3390/polym12102220
Omer MAE, Shaban IA, Mourad A-H, et al. Advances in interlayer bonding in fused deposition modelling: a comprehensive review. Virtual and Physical Prototyping 2025; 20(1). https://doi.org/10.1080/17452759.2025.2522951
Zohdi N, Yang RC. Material Anisotropy in Additively Manufactured Polymers and Polymer Composites: A Review. Polymers (Basel) 2021; 13(19). https://doi.org/10.3390/polym13193368
Madhavan Nampoothiri K, Nair NR, John RP. An overview of the recent developments in polylactide (PLA) research. Bioresour Technol 2010; 101(22): 8493-501. https://doi.org/10.1016/j.biortech.2010.05.092
Arrigo R, Frache A. FDM Printability of PLA Based-Materials: The Key Role of the Rheological Behavior. Polymers (Basel) 2022; 14(9). https://doi.org/10.3390/polym14091754
Changhui L, Hao L, Chunlong Y, et al. Balanced Optimization of Dimensional Accuracy and Printing Efficiency in FDM Based on Data-Driven Modeling. Additive Manufacturing Frontiers 2025; 4(2). https://doi.org/10.1016/j.amf.2025.200220
Sukumaar VN, Rangappa SM, Liu Y, et al. A comprehensive review on the influence of fused deposition modelling process parameters upon thermoplastic composite materials. Advanced Industrial and Engineering Polymer Research 2026; 9(2): 281-303. https://doi.org/10.1016/j.aiepr.2025.11.006
Layeb N, Oldal I, Zsidai L. Flexural strength evolution of 3D printed PLA-CF structures: optimization of FDM parameters for enhanced mechanical performance. Journal of Materials Science: Materials in Engineering 2026; 21(1). https://doi.org/10.1186/s40712-026-00424-x
Plamadiala I, Croitoru C, Pop MA, et al. Enhancing Polylactic Acid (PLA) Performance: A Review of Additives in Fused Deposition Modelling (FDM) Filaments. Polymers (Basel) 2025; 17(2). https://doi.org/10.3390/polym17020191
Haque MMM, Dhrubo SR, Pranto A-FZ, et al. Impact of process parameters and material selection on the mechanical performance of FDM 3D-Printed components. Hybrid Advances 2025; 10. https://doi.org/10.1016/j.hybadv.2025.100502
Kamaal M, Anas M, Rastogi H, et al. Effect of FDM process parameters on mechanical properties of 3D-printed carbon fibre–PLA composite. Progress in Additive Manufacturing 2020; 6(1): 63-9. https://doi.org/10.1007/s40964-020-00145-3
Wickramasinghe S, Do T, Tran P. FDM-Based 3D Printing of Polymer and Associated Composite: A Review on Mechanical Properties, Defects and Treatments. Polymers (Basel) 2020; 12(7). https://doi.org/10.3390/polym12071529
Bhandari S, Lopez-Anido RA, Gardner DJ. Enhancing the interlayer tensile strength of 3D printed short carbon fiber reinforced PETG and PLA composites via annealing. Additive Manufacturing 2019; 30. https://doi.org/10.1016/j.addma.2019.100922
Butt J, Khan MAA, Adnan M, et al. Performance Analysis of FFF-Printed Carbon Fiber Composites Subjected to Different Annealing Methods. Journal of Manufacturing and Materials Processing 2024; 8(6). https://doi.org/10.3390/jmmp8060252
Papon EA, Haque A, Spear SK. Effects of functionalization and annealing in enhancing the interfacial bonding and mechanical properties of 3D printed fiber-reinforced composites. Materials Today Communications 2020; 25. https://doi.org/10.1016/j.mtcomm.2020.101365
